The image size increased in 8.0.1-BETA3. The new size requires a 2 GB storage device. The GUI upgrade can be used to upgrade a system from BETA3, BETA4, or RC1 but upgrades from earlier releases can only be done from the CD. The other option is to save the config, reinstall the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update your BIOS/BMC firmware when upgrading / installing FreeNAS if you run into OS hang issues. There have been cases identified where a BIOS upgrade has fixed driver hangs, and/or other issues with FreeNAS; one such example was with an Intel 82578DC motherboard, as noted in the FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..": http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you experience booting / runtime issues, as some vendors don't test FreeBSD interoperability as much as others between major firmware releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64, respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but 8.0.3 and later images don't advertise CIFS shares by default. If you want to advertise CIFS shares in 8.0.3 and later, be sure to turn on "Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO (asynchronous I/O) enabled. So, if you experience performance degradation after upgrading from prior versions of FreeNAS to 8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096 or 4kB).
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from
BETA3, BETA4, or RC1 but upgrades from earlier releases can only be
done from the CD. The other option is to save the config, reinstall
the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update
your BIOS/BMC firmware when upgrading / installing FreeNAS if you run
into OS hang issues. There have been cases identified where a BIOS
upgrade has fixed driver hangs, and/or other issues with FreeNAS; one
such example was with an Intel 82578DC motherboard, as noted in the
FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..":
http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you
experience booting / runtime issues, as some vendors don't test
FreeBSD interoperability as much as others between major firmware
releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit
respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64,
respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but
8.0.3 and later images don't advertise CIFS shares by default. If you
want to advertise CIFS shares in 8.0.3 and later, be sure to turn on
"Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO
(asynchronous I/O) enabled. So, if you experience performance
degradation after upgrading from prior versions of FreeNAS to
8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to
something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096
or 4kB).
URGENT
FreeNAS 8.0.4 and earlier may be affected by a critical Samba vulnerability - all users who use CIFS are urged to update.
*** IMPORTANT ***
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB storage device. The GUI upgrade can be used to upgrade a system from BETA3, BETA4, or RC1 but upgrades from earlier releases can only be done from the CD. The other option is to save the config, reinstall the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update your BIOS/BMC firmware when upgrading / installing FreeNAS if you run into OS hang issues. There have been cases identified where a BIOS upgrade has fixed driver hangs, and/or other issues with FreeNAS; one such example was with an Intel 82578DC motherboard, as noted in the FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..": http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you experience booting / runtime issues, as some vendors don't test FreeBSD interoperability as much as others between major firmware releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64, respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but 8.0.3 and later images don't advertise CIFS shares by default. If you want to advertise CIFS shares in 8.0.3 and later, be sure to turn on "Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO (asynchronous I/O) enabled. So, if you experience performance degradation after upgrading from prior versions of FreeNAS to 8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096 or 4kB).
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from
BETA3, BETA4, or RC1 but upgrades from earlier releases can only be
done from the CD. The other option is to save the config, reinstall
the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update
your BIOS/BMC firmware when upgrading / installing FreeNAS if you run
into OS hang issues. There have been cases identified where a BIOS
upgrade has fixed driver hangs, and/or other issues with FreeNAS; one
such example was with an Intel 82578DC motherboard, as noted in the
FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..":
http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you
experience booting / runtime issues, as some vendors don't test
FreeBSD interoperability as much as others between major firmware
releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit
respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64,
respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but
8.0.3 and later images don't advertise CIFS shares by default. If you
want to advertise CIFS shares in 8.0.3 and later, be sure to turn on
"Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO
(asynchronous I/O) enabled. So, if you experience performance
degradation after upgrading from prior versions of FreeNAS to
8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to
something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096
or 4kB).
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from
BETA3, BETA4, or RC1 but upgrades from earlier releases can only be
done from the CD. The other option is to save the config, reinstall
the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update
your BIOS/BMC firmware when upgrading / installing FreeNAS if you run
into OS hang issues. There have been cases identified where a BIOS
upgrade has fixed driver hangs, and/or other issues with FreeNAS; one
such example was with an Intel 82578DC motherboard, as noted in the
FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..":
http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you
experience booting / runtime issues, as some vendors don't test
FreeBSD interoperability as much as others between major firmware
releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit
respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64,
respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but
8.0.3 and later images don't advertise CIFS shares by default. If you
want to advertise CIFS shares in 8.0.3 and later, be sure to turn on
"Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO
(asynchronous I/O) enabled. So, if you experience performance
degradation after upgrading from prior versions of FreeNAS to
8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to
something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096
or 4kB).
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from
BETA3, BETA4, or RC1 but upgrades from earlier releases can only be
done from the CD. The other option is to save the config, reinstall
the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update
your BIOS/BMC firmware when upgrading / installing FreeNAS if you run
into OS hang issues. There have been cases identified where a BIOS
upgrade has fixed driver hangs, and/or other issues with FreeNAS; one
such example was with an Intel 82578DC motherboard, as noted in the
FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..":
http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you
experience booting / runtime issues, as some vendors don't test
FreeBSD interoperability as much as others between major firmware
releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit
respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64,
respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but
8.0.3 and later images don't advertise CIFS shares by default. If you
want to advertise CIFS shares in 8.0.3 and later, be sure to turn on
"Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO
(asynchronous I/O) enabled. So, if you experience performance
degradation after upgrading from prior versions of FreeNAS to
8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to
something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096
or 4kB).
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from
BETA3, BETA4, or RC1 but upgrades from earlier releases can only be
done from the CD. The other option is to save the config, reinstall
the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update
your BIOS/BMC firmware when upgrading / installing FreeNAS if you run
into OS hang issues. There have been cases identified where a BIOS
upgrade has fixed driver hangs, and/or other issues with FreeNAS; one
such example was with an Intel 82578DC motherboard, as noted in the
FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..":
http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you
experience booting / runtime issues, as some vendors don't test
FreeBSD interoperability as much as others between major firmware
releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit
respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64,
respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but
8.0.3 and later images don't advertise CIFS shares by default. If you
want to advertise CIFS shares in 8.0.3 and later, be sure to turn on
"Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO
(asynchronous I/O) enabled. So, if you experience performance
degradation after upgrading from prior versions of FreeNAS to
8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to
something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096
or 4kB).
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB storage device. The GUI upgrade can be used to upgrade a system from BETA3, BETA4, or RC1 but upgrades from earlier releases can only be done from the CD. The other option is to save the config, reinstall the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update your BIOS/BMC firmware when upgrading / installing FreeNAS if you run into OS hang issues. There have been cases identified where a BIOS upgrade has fixed driver hangs, and/or other issues with FreeNAS; one such example was with an Intel 82578DC motherboard, as noted in the FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..": http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you experience booting / runtime issues, as some vendors don't test FreeBSD interoperability as much as others between major firmware releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64, respectively.
8.0.1 and 8.0.2 images advertised CIFS shares to Macs by default but 8.0.3 and later images don't advertise CIFS shares by default. If you want to advertise CIFS shares in 8.0.3 and later, be sure to turn on "Zeroconf" support in the CIFS global settings.
Builds prior to 8.0.3-RELEASE with 'CIFS' didn't actually have AIO (asynchronous I/O) enabled. So, if you experience performance degradation after upgrading from prior versions of FreeNAS to 8.0.3-RELEASE or newer, turn off AIO or tune the AIO size from '1' to something more reasonable (the new default in 8.0.3-RELEASE-p1 is 4096 or 4kB).
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from
BETA3, BETA4, or RC1 but upgrades from earlier releases can only be
done from the CD. The other option is to save the config, reinstall
the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update
your BIOS/BMC firmware when upgrading / installing FreeNAS if you run
into OS hang issues. There have been cases identified where a BIOS
upgrade has fixed driver hangs, and/or other issues with FreeNAS; one
such example was with an Intel 82578DC motherboard, as noted in the
FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..":
http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you
experience booting / runtime issues, as some vendors don't test
FreeBSD interoperability as much as others between major firmware
releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit
respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64,
respectively.
Due to our busy schedule we will not be styling the release notes for you. Don't fret! Allow us to give you a direct link to the README hosted on SourceForge along with the directory containing all the install images one could ever need.
There are some things to note about this Release Candidate, please read on.
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from
BETA3, BETA4, or RC1 but upgrades from earlier releases can only be
done from the CD. The other option is to save the config, reinstall
the new version, then restore the config.
FreeBSD can be really touchy with hardware. Please be sure to update
your BIOS/BMC firmware when upgrading / installing FreeNAS if you run
into OS hang issues. There have been cases identified where a BIOS
upgrade has fixed driver hangs, and/or other issues with FreeNAS; one
such example was with an Intel 82578DC motherboard, as noted in the
FreeNAS 8 forum thread titled "8.0.3-RELEASE coming soon..":
http://bit.ly/rq78Q3 , post # 70-88. Again, please only do this if you
experience booting / runtime issues, as some vendors don't test
FreeBSD interoperability as much as others between major firmware
releases.
Previous builds were branded as i386/amd64 (32-bit and 64-bit
respectively). 8.0.3-RC1+ rebranded the architectures as x86 and x64,
respectively.
The FreeNAS team is pleased to announce FreeNAS 8.0.2-RELEASE. This can be considered a minor release that fixes a few of the more glaring issues in 8.0.1-RELEASE.
The FreeNAS Development Team is pleased to announce the release of FreeNAS 8.0.1.
*** IMPORTANT ***
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB storage device. The GUI upgrade can be used to upgrade a system from BETA3, BETA4, RC1 or RC2 but upgrades from earlier releases can only be done from the CD.
The other option is to save the config, reinstall the new version, then restore the config.
This is Release Candidate 2 for FreeNAS 8.0.1....hopefully the last stepping
stone to FreeNAS 8.0.1-RELEASE
*** IMPORTANT ***
The image size increased in 8.0.1-BETA3. The new size requires a 2 GB
storage device. The GUI upgrade can be used to upgrade a system from BETA3,
BETA4, or RC1 but upgrades from earlier releases can only be done from the CD.
The other option is to save the config, reinstall the new version, then
restore the config.
